Call Today

We have noticed this post about How to Install a Bathtub directly below on the net and reckoned it made sense to share it with you here.

Mounting a bathtub isn't precisely rocket science, but it does require solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a brand-new one is also a reasonably tough project. If the old tub is easily accessible, the task can relocate immediately; if you need to open up a wall to eliminate the old tub and position the brand-new bathtub, the job is a lot harder. In either situation, the task is within a house handyman's abilities, although you will need a helper to leave the old tub and also set in the new one. Make sure you have certified yourself for the task and also are comfortable trying it. Rather than hiring a contractor to take over a halfway-completed job, it is much better to take into consideration employing one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This article will certainly aid you set up a brand-new bath tub in your restroom if you have actually currently bought a new bathtub as well as don't need to transform the arrangement of your previous supply of water pipelines.
Your devices as well as product checklist ought to comprise the following:

• New Tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you should do is separate the water supply. After doing so, switch on the taps to drain any water staying in the system. The procedure of eliminating the existing taps can be quite problematic because of the restricted access that is usually the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipes to the taps. Have a cloth all set for the remaining water that will certainly come from the pipelines. When the supply pipes have been removed, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the taps have been removed, the holes in the bath/basin will have to be cleaned of any kind of old sealing substance.
Prior to proceeding to fit the brand-new taps, compare the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new taps, after that a shank adapter is required for the brand-new faucets to fit.

Fitting New Taps

If the tails of the new taps are plastic, then you will certainly require a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the faucet and the other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin making certain that the washing machines remain in place in between the faucet as well as the sink. Safeguard the tap in place with the producer given backnut. As soon as the tap is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by using corrugated copper piping or with typical tap ports. The former kind ought to be attached to the faucet finishes first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.

Setting up the Bath tub

Using both wooden boards under its feet, put the bath tub in the called for position. The wooden boards are practical in equally spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto four little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the tub until the spirit level reviews degree.
To install taps, fit all-time low of the outermost versatile tap adapter to the suitable supply pipe by making a compression sign up with; then do the very same for the various other tap.
Activate the water system and also inspect all joints and also new pipework for leaks as well as tighten them if essential. Load the tub and also inspect the overflow electrical outlet and also the regular electrical outlet for leaks.
Lastly, deal with the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the bathtub needs to wait until the bath tub has been made use of at the very least once as this will certainly settle it into its last setting.

Getting ready for the Installation

First of all, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps system to avoid pressure on the tub.
Fit the adaptable faucet ports to the bottom of the two taps making use of 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you use all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final position.

Tiling Around the Bath tub

In the area where the bathroom fulfills the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the fitting can relocate sufficient to crack a stiff seal, causing the water to permeate the wall in between the bathroom as well as the tiling, resulting in complications with wetness and also feasible leakages to the ceiling listed below.
You can pick from a range of coloured sealants to assimilate your components and fittings. They are offered in tubes and also cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Remember to constantly load the bath tub with water before sealing, to enable the movement experienced when the bathtub remains in usage. The sealant can break relatively early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the marketplace. It is advisable to fit the floor tiles utilizing waterproof or water resistant sticky as well as grout.

Bathtub Installation

How Important Is A Bathtub To Your Home?

High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.

Install Piping Before Tub

You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.

Position the Tub

Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.

 

NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.

Assemble Drain Connections

Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.

Place a Pipe For the Shower Head

First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.

Attaching Hot and Cold Water Lines

Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.

Install the Spout

Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.

 

NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.

Check For Leaks

Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.

estore the Bathroom Wall

Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/

Do you appreciate reading up on A Step-by-Step Guide to Installing a Bathtub? Try leaving a comment down the page. We will be interested to know your feelings about this page. In hopes that you visit us again in the future. Remember to take a moment to promote this content if you enjoyed it. Thank you for taking the time to read it.

Estimate Free